V3F drive for MX18 gearless Axial Machinery
Table of Contents
V3F drive for MX18 gearless Axial Machinery
KM781380G01 V3F25/V3F18 HCBN ASSEMBLY
Gross weight: 0,45
KM781380G02
V3F25/V3F18 HCBN ASSEMBLY
KM781380G11
PCB,HCBN V3F18 V3F25
KM781380G03
PCB, MOTION CONTROL HCBN V3F18
KM733473G01
Replaced by KM781380G01
MOTION CNTL BD,HCB,V3F-25
Component Family Codes
V3F18 – Drive System for Big Monospace (MX20)
V3F25 – V3F drive for MX18 gearless Axial Machinery.
ZZ-006 – PSR – Pre-defined packages
Product Description
hu: A1-ES PANEL V3F25/V3F18
vi: Bo giao ti?p HCBN bi?n t?n V3F25/V3F18
fr: CARTE CDE HCB (385
sl: EL. ZA NADZOR GIBANJA HCBN V3F25 / V3F18
zf: HCB 板 781380G01
sv: KRETSKORT HCB
it: MOTION CONTROL PCB,HCB V3F25
tr: PCB,MOTION CONTROL HCBN V3F18
fi: PIIRIKORTTI HCB V3F25
es: PLACA HCB / V3F25 385:A1 R/733473G01
de: PLATINE HCB V3F18/25
da: Printkort HCB
zh: V3F25/V3F16 速度线路板
en: V3F25/V3F18 HCBN ASSEMBLY
ru: Печатная плата
Product Family Codes
KONE 3000 MiniSpace
KONE 3000S Monospace
KONE Alta
KONE MiniSpace
KONE MonoSpace Special
KONE TranSys
Ordering the v3f drive
To order the v3f drive, send us a photograph of the existing unit and its nameplate at [email protected]. Please quote the complete code including any revision suffix so that our team can confirm the correct variant, current stock and lead time before you commit.
About the v3f drive
Elevator and escalator installations are built around a relatively small number of serviceable assemblies, but they fail at very different rates. The v3f drive sits in the chains / belts / drives group, and it is replaced on a different service interval from the assemblies around it. In practice the failures we see on v3f drive come down to pitch elongation beyond the wear limit, seized rollers, and sprockets whose tooth profile has hooked after running with a stretched chain.
Every v3f drive we supply is inspected before dispatch. Each unit is checked for physical damage, correct marking and the specific wear or degradation patterns that matter for this class of component, then packed to survive international transit. Where a superseded revision is the only one available, we say so plainly and explain the substitution, so the installing engineer can make an informed decision rather than discovering the difference on site.
Buying guidance and compatibility notes
Before ordering the v3f drive, confirm three things. First, the chain pitch, link count and the number of strands, since a duplex chain will not substitute for a simplex one. Second, chain numbers are frequently local to a manufacturer, so we match on pitch and link count rather than on the printed number alone. Third, whether the installation is a traction lift or an escalator, since duty cycle and loading differ between the two.
On fitting, one point is worth repeating: always measure elongation across at least twenty pitches — a chain that looks acceptable over five links is often past its limit overall. Almost every repeat failure we see on v3f drive traces back to a related component that was left in place, or to an adjustment that was assumed rather than measured.
If you are unsure which variant of the v3f drive you need, send a photograph of the nameplate and the existing component alongside a description of the fault. That is usually enough for our team to identify the correct replacement without a site visit, and it avoids the cost and delay of returning an incompatible part. We are also happy to advise on the other serviceable items in the same chains / belts / drives group, so a planned shutdown can cover several wear items at once.
Related parts and further reading
Because v3f drive is only one item in the chains / belts / drives group, these related pages may help you plan the work:
- Handrail drive chains
- Escalator Main Drive Chain
- Escalator Step Chain
- Step Chain Sprocket
- Step Chain Tensioner
Reference sources
The compatibility information on this page was cross-checked against the following authoritative references. Always confirm the exact reference against your own equipment nameplate.
