lift inverter KDL16S KM51004000V002

KDL16S KONE elevator drive inverter KM51004000V001
Kone elevator drive module assembly KM968094G03 KDL16S 20A
Kone Inverter lift inverter KDL16S KM51004000V002

KM1349540G02/KM1349547G01 Braking resistor module KDL16/KDL16S/KDL16R

KM51004000V001
KDL16S, 12A, IP23, BMV R
Gross weight: 18,89kg

KM51004000V002
KDL16S, 20A, IP23, BMV R
Gross weight: 19,05kg

Ordering the lift inverter kdl16s

To order the lift inverter kdl16s, send us a photograph of the existing unit and its nameplate at [email protected]. Please quote the complete code including any revision suffix so that our team can confirm the correct variant, current stock and lead time before you commit.

About the lift inverter kdl16s

Elevator and escalator installations are built around a relatively small number of serviceable assemblies, but they fail at very different rates. The lift inverter kdl16s sits in the control board / PCB group, and it is replaced on a different service interval from the assemblies around it. In practice the failures we see on lift inverter kdl16s come down to electrolytic capacitor ageing, cracked solder joints around the power stage, corroded edge connectors, and blown output transistors after a supply fault.

Every lift inverter kdl16s we supply is inspected before dispatch. Each unit is checked for physical damage, correct marking and the specific wear or degradation patterns that matter for this class of component, then packed to survive international transit. Where a superseded revision is the only one available, we say so plainly and explain the substitution, so the installing engineer can make an informed decision rather than discovering the difference on site.

Buying guidance and compatibility notes

Before ordering the lift inverter kdl16s, confirm three things. First, the controller catalogue number and the board revision letter, plus the fault code stored in the controller memory. Second, the same board is frequently fitted across several controller families, so the equipment model alone is not enough to identify the right revision. Third, whether the installation is a traction lift or an escalator, since duty cycle and loading differ between the two.

On fitting, one point is worth repeating: discharge the DC bus before removing a power board, and photograph the connector layout before you unplug anything. Almost every repeat failure we see on lift inverter kdl16s traces back to a related component that was left in place, or to an adjustment that was assumed rather than measured.

When a drive or mother board is replaced, it is worth checking the DC bus capacitors and the cooling path at the same time. A board that failed from overheating will fail again if the fan or heatsink is left as it was.

Drive and logic electronics sit at the centre of every modern installation, and the symptom that most often brings an engineer to it is a lift that travels but refuses to level or open its doors.

Anti-static handling is not a formality. A board that works perfectly on the bench can be destroyed by a discharge too small for a technician to feel, which is why stock travels in shielded bags and is unpacked only at the point of fitting.

If you are unsure which variant of the lift inverter kdl16s you need, send a photograph of the nameplate and the existing component alongside a description of the fault. That is usually enough for our team to identify the correct replacement without a site visit, and it avoids the cost and delay of returning an incompatible part. We are also happy to advise on the other serviceable items in the same control board / PCB group, so a planned shutdown can cover several wear items at once.

Related parts and further reading

Because lift inverter kdl16s is only one item in the control board / PCB group, these related pages may help you plan the work:

• Elevator spare parts
• Door Operator Controller
• Elevator Display
• Elevator Encoder
• Elevator Service Tool

Reference sources

The compatibility information on this page was cross-checked against the following authoritative references. Always confirm the exact reference against your own equipment nameplate.

• ISO 8100-1 — lift safety standard
• IEC — international electrotechnical standards
• Otis genuine parts reference