NBSL XSQ115-02 speed governor
Table of Contents
NBSL XSQ115-02 speed governor
NBSL XSQ115-02 speed governor
Elevator speed governor made by ningbo senling elevator components co,. ltd
This speed governor also have XSQ115-02 XSQ115-10 XSQ115-12 XSQ115-13.
Otis speed governor parts numnber is DCA20602C
NBSL XSQ115 Support OTIS KONE and Gaintkone elevator installation.
The below running speed is supported.
0.5m/s wirerope diameter 6.3mm
0.63m/s wirerope diameter 6.3mm
1m/s wirerope diameter 6.3mm
1m/s wirerope diameter 8mm
1.5m/s wirerope diameter 8mm
1.6m/s wirerope diameter 8mm
1.75m/s wirerope diameter 8mm
2m/s wirerope diameter 8mm
2.5m/s wirerope diameter 8mm
Ordering the nbsl xsq115-02 speed
To order the nbsl xsq115-02 speed, send us a photograph of the existing unit and its nameplate at [email protected]. Please quote the complete code including any revision suffix so that our team can confirm the correct variant, current stock and lead time before you commit.
About the nbsl xsq115-02 speed
Elevator and escalator installations are built around a relatively small number of serviceable assemblies, but they fail at very different rates. The nbsl xsq115-02 speed sits in the brake / safety gear group, and it is replaced on a different service interval from the assemblies around it. In practice the failures we see on nbsl xsq115-02 speed come down to glazed or oil-contaminated linings, weak coils, worn pivot bushes, and spring sets that have lost their rated tension.
Every nbsl xsq115-02 speed we supply is inspected before dispatch. Each unit is checked for physical damage, correct marking and the specific wear or degradation patterns that matter for this class of component, then packed to survive international transit. Where a superseded revision is the only one available, we say so plainly and explain the substitution, so the installing engineer can make an informed decision rather than discovering the difference on site.
Buying guidance and compatibility notes
Before ordering the nbsl xsq115-02 speed, confirm three things. First, the brake model, the drum or disc diameter, and the rated torque shown on the original rating plate. Second, brake units are often shared between a traction machine and its close relatives, but the lining grade can differ with the duty rating. Third, whether the installation is a traction lift or an escalator, since duty cycle and loading differ between the two.
On fitting, one point is worth repeating: brake springs and linings should always be replaced as a matched set, and the air gap re-measured to the manufacturer figure afterwards. Almost every repeat failure we see on nbsl xsq115-02 speed traces back to a related component that was left in place, or to an adjustment that was assumed rather than measured.
If you are unsure which variant of the nbsl xsq115-02 speed you need, send a photograph of the nameplate and the existing component alongside a description of the fault. That is usually enough for our team to identify the correct replacement without a site visit, and it avoids the cost and delay of returning an incompatible part. We are also happy to advise on the other serviceable items in the same brake / safety gear group, so a planned shutdown can cover several wear items at once.
Related parts and further reading
Because nbsl xsq115-02 speed is only one item in the brake / safety gear group, these related pages may help you plan the work:
- Elevator brake linings
- Escalator Brake Lining
- Elevator Limit Switch
- Elevator Load Weighing Device
- Elevator Guide Shoe
Reference sources
The compatibility information on this page was cross-checked against the following authoritative references. Always confirm the exact reference against your own equipment nameplate.
reza
hi
I need certificate of governor and image of name plate
[email protected]
Hello Reza,
How are you.
Certificate of governor are send together with the goods, we can’t just offer it to you.
And please check the name plate