KONE LCECOB KM713720G11

KONE LCECOB COP board
KM713720G11 / G51 / G71 / G01
One year warranty

KONE LCECOB KM713720G01

KONE LCECOB KM713720G11

KONE LCECOB KM713720G51

KONE LCECOB KM713720G71

Ordering the kone lcecob km713720g11

To order the kone lcecob km713720g11, send us a photograph of the existing unit and its nameplate at [email protected]. Please quote the complete code including any revision suffix so that our team can confirm the correct variant, current stock and lead time before you commit.

About the kone lcecob km713720g11

Elevator and escalator installations are built around a relatively small number of serviceable assemblies, but they fail at very different rates. The kone lcecob km713720g11 sits in the control board / PCB group, and it is replaced on a different service interval from the assemblies around it. In practice the failures we see on kone lcecob km713720g11 come down to electrolytic capacitor ageing, cracked solder joints around the power stage, corroded edge connectors, and blown output transistors after a supply fault.

Every kone lcecob km713720g11 we supply is inspected before dispatch. Each unit is checked for physical damage, correct marking and the specific wear or degradation patterns that matter for this class of component, then packed to survive international transit. Where a superseded revision is the only one available, we say so plainly and explain the substitution, so the installing engineer can make an informed decision rather than discovering the difference on site.

Buying guidance and compatibility notes

Before ordering the kone lcecob km713720g11, confirm three things. First, the controller catalogue number and the board revision letter, plus the fault code stored in the controller memory. Second, the same board is frequently fitted across several controller families, so the equipment model alone is not enough to identify the right revision. Third, whether the installation is a traction lift or an escalator, since duty cycle and loading differ between the two.

On fitting, one point is worth repeating: discharge the DC bus before removing a power board, and photograph the connector layout before you unplug anything. Almost every repeat failure we see on kone lcecob km713720g11 traces back to a related component that was left in place, or to an adjustment that was assumed rather than measured.

Bench testing before dispatch catches the majority of faulty stock. Boards are powered up, exercised through their diagnostic modes where the manufacturer supports it, and checked for the specific failure modes that matter in service rather than for cosmetic condition.

A unit showing an intermittent stop at a random floor with no repeatable pattern is usually telling you that the cooling path and DC bus capacitors are flagged as items to check at the same time.

Anti-static handling is not a formality. A board that works perfectly on the bench can be destroyed by a discharge too small for a technician to feel, which is why stock travels in shielded bags and is unpacked only at the point of fitting.

When a customer reports a lift that travels but refuses to level or open its doors, our first question is about firmware that no longer matches the parameters loaded into the controller rather than about the electronics.

Connector condition deserves more attention than it usually gets. Edge connectors oxidise, ribbon cables develop hairline fractures at the fold, and a board that tests perfectly on the bench can fail intermittently once fitted because the fault was in the harness all along.

If you are unsure which variant of the kone lcecob km713720g11 you need, send a photograph of the nameplate and the existing component alongside a description of the fault. That is usually enough for our team to identify the correct replacement without a site visit, and it avoids the cost and delay of returning an incompatible part. We are also happy to advise on the other serviceable items in the same control board / PCB group, so a planned shutdown can cover several wear items at once.

Related parts and further reading

Because kone lcecob km713720g11 is only one item in the control board / PCB group, these related pages may help you plan the work:

• Elevator spare parts
• Door Operator Controller
• Elevator Display
• Elevator Encoder
• Elevator Service Tool

Reference sources

The compatibility information on this page was cross-checked against the following authoritative references. Always confirm the exact reference against your own equipment nameplate.

• ISO 8100-1 — lift safety standard
• IEC — international electrotechnical standards
• Otis genuine parts reference