Kone Elevator V3F16L inverter A2 Drive board

KM825950G01 KM825953H03
Kone Elevator V3F16L inverter A2 Drive board

825953 H03/769853 H06

Make sure the test is normal before sending out.
This board has been stop produce for many years, only have second-hand ones in the market.
We provide mainboard renovation service, which can reach more than 95% NEW.
It can be as good as the new one.

Kone Km769853 board is MCDLc PCB

Description : Kone Board；KM825950G01
Specification : Original&New
Original P/N : KM825950G01
Suitable Brand : Kone
Origin : Made In China
Categories : BRAND, Controller System & Related, Elevator, Kone, PCBs

Ordering the kone elevator v3f16l

To order the kone elevator v3f16l, send us a photograph of the existing unit and its nameplate at [email protected]. Please quote the complete code including any revision suffix so that our team can confirm the correct variant, current stock and lead time before you commit.

About the kone elevator v3f16l

Elevator and escalator installations are built around a relatively small number of serviceable assemblies, but they fail at very different rates. The kone elevator v3f16l sits in the control board / PCB group, and it is replaced on a different service interval from the assemblies around it. In practice the failures we see on kone elevator v3f16l come down to electrolytic capacitor ageing, cracked solder joints around the power stage, corroded edge connectors, and blown output transistors after a supply fault.

Every kone elevator v3f16l we supply is inspected before dispatch. Each unit is checked for physical damage, correct marking and the specific wear or degradation patterns that matter for this class of component, then packed to survive international transit. Where a superseded revision is the only one available, we say so plainly and explain the substitution, so the installing engineer can make an informed decision rather than discovering the difference on site.

Buying guidance and compatibility notes

Before ordering the kone elevator v3f16l, confirm three things. First, the controller catalogue number and the board revision letter, plus the fault code stored in the controller memory. Second, the same board is frequently fitted across several controller families, so the equipment model alone is not enough to identify the right revision. Third, whether the installation is a traction lift or an escalator, since duty cycle and loading differ between the two.

On fitting, one point is worth repeating: discharge the DC bus before removing a power board, and photograph the connector layout before you unplug anything. Almost every repeat failure we see on kone elevator v3f16l traces back to a related component that was left in place, or to an adjustment that was assumed rather than measured.

Control electronics dominate the failure statistics on any lift older than about twelve years. The boards themselves are usually sound; what fails is the surrounding hardware — capacitors that have dried out, connectors that have oxidised in a humid machine room, and solder joints that have cracked under years of thermal cycling.

If the installation is showing a drive that trips on acceleration but runs normally at low speed, the identification route is straightforward: the controller catalogue number, the board revision letter and any fault code stored in memory are the three details that let us identify the part without guesswork.

If you are unsure which variant of the kone elevator v3f16l you need, send a photograph of the nameplate and the existing component alongside a description of the fault. That is usually enough for our team to identify the correct replacement without a site visit, and it avoids the cost and delay of returning an incompatible part. We are also happy to advise on the other serviceable items in the same control board / PCB group, so a planned shutdown can cover several wear items at once.

Related parts and further reading

Because kone elevator v3f16l is only one item in the control board / PCB group, these related pages may help you plan the work:

• Elevator spare parts
• Door Operator Controller
• Elevator Display
• Elevator Encoder
• Elevator Service Tool

Reference sources

The compatibility information on this page was cross-checked against the following authoritative references. Always confirm the exact reference against your own equipment nameplate.

• ISO 8100-1 — lift safety standard
• IEC — international electrotechnical standards
• Otis genuine parts reference