Kone STNLCD_H_5.7 display
Table of Contents
Kone STNLCD_H_5.7 display
Kone STNLCD_H_5.7 display
KM51167889G02 KM51104210H01
The model numbers of all other KONE monitors in this series are as follows
KM51167889G02
NEW STNLCD_H_5.7BLACK ASSEMBLY,WITH GONG
KM51167889G03
NEW STNLCD_H_5.7 PCBA,BLACK FOR COP
KM51104206G01
STNLCD_V_5.7(Re-layout) BLUE ASSEMBLY
KM51104209G12
STNLCD_H_5.7(Re-layout) BLACK ASSEMBLY
KM51104209G02
STNLCD_H_5.7(RE-LAYOUT) BLUE ASSEMBLY
About kone elevator and escalator parts
To order kone elevator and escalator parts, send the exact model or reference code printed on the original component to [email protected]. Please quote the complete code including any suffix so that our team can confirm the correct variant, current stock and lead time before you commit.
What we supply for kone
Elevator and escalator installations are built around a relatively small number of serviceable assemblies, but they fail at very different rates. We stock kone parts covering the items that fail most often in daily service. In practice the failures we see on kone elevator and escalator parts come down to contact pitting, moisture ingress at the cable gland, drifted optical alignment, and brittle insulation on travelling cables after years of flexing.
All kone parts we supply are inspected before dispatch. Each unit is checked for physical damage, correct marking and the specific wear or degradation patterns that matter for this class of component, then packed to survive international transit. Where a superseded revision is the only one available, we say so plainly and explain the substitution, so the installing engineer can make an informed decision rather than discovering the difference on site.
Buying guidance and compatibility notes
Before ordering kone elevator and escalator parts, confirm three things. First, the switch or sensor model, the mounting pattern, and the supply voltage and contact configuration (NO or NC). Second, contact configuration matters more than physical size — a switch that bolts straight on can still be electrically wrong. Third, whether the installation is a traction lift or an escalator, since duty cycle and loading differ between the two.
On fitting, one point is worth repeating: record the terminal numbers before disconnecting a travelling cable, since colour codes are not consistent between controller generations. Almost every repeat failure we see on kone elevator and escalator parts traces back to a related component that was left in place, or to an adjustment that was assumed rather than measured.
Levelling and position sensing are unforgiving of drift. A sensor that has moved by a millimetre, or a vane that has been nudged during maintenance, can produce a fault that appears intermittently and is difficult to reproduce on a service visit.
Electrical components in a lift work in an environment that is hostile to all of them; inductive switching duty shortens contact life dramatically compared with a resistive load of the same rating.
Displays, buttons and intercoms are passenger-facing, so their failure is immediately visible and often reported before any technical diagnosis is possible. Keeping common faceplates and modules in stock shortens the outage considerably.
Where the root cause is contact pitting that increases resistance without breaking the circuit, in our experience the contact configuration is confirmed as normally-open or normally-closed before dispatch, because that matters more than physical fit.
Inductive loads are hard on switching contacts. A contactor or relay that switches a motor or a coil will pit far faster than one carrying a resistive load of the same rating, which is why the same physical device can last years in one position and months in another.
If you are unsure which variant of the kone elevator and escalator parts you need, send a photograph of the nameplate and the existing component alongside a description of the fault. That is usually enough for our team to identify the correct replacement without a site visit, and it avoids the cost and delay of returning an incompatible part. We are also happy to advise on the other serviceable items in the same switches / sensors / wiring group, so a planned shutdown can cover several wear items at once.
Related parts and further reading
Because kone elevator and escalator parts is only one item in the switches / sensors / wiring group, these related pages may help you plan the work:
- Elevator limit switches
- Elevator Levelling Sensor
- Elevator Encoder
- Elevator Push Button
- Elevator Display
Reference sources
The compatibility information on this page was cross-checked against the following authoritative references. Always confirm the exact reference against your own equipment nameplate.
