KDM Inverter KM997159_local
Table of Contents
KDM Inverter KM997159_local
KDM40 KONE inverter
100% new with original package.
Kone Ac Drive
Type: KM997159_Local
Input: 400V,50-60Hz,32A
Output: 0-Uin,0-250Hz,40A
Power: 22KW
Fireware: FW0077V107
Made by Kone elevators co,. ltd(soc)
Made in china(PRC)
Kone Elevator KDM Inverter KM997159_local
New and original KONE KM997159_LOCAL INVERTER ,KONE KM997160_LOCAL INVERTER
KM997159 KN KDM DRIVE KM997159 KM997159-LOCAL Drive 40A KDM40A KN elevator parts
KONE Elevator Drive inverter KDM KM997159_LOCAL 22KW
KONE elevator spare parts ,KM997159 Kone KDM Inverter 40A kone LOCAL
Ordering the kdm inverter
To order the kdm inverter, send the exact model or reference code printed on the original part to [email protected]. Please quote the full code including any suffix so that our team can confirm the correct variant, current stock and lead time before you commit.
About the kdm inverter
Elevator and escalator installations are built around a relatively small number of serviceable assemblies, but they fail at very different rates. The kdm inverter sits in the control board / PCB group, and it is replaced on a different service interval from the assemblies around it. In practice the failures we see on kdm inverter come down to electrolytic capacitor ageing, cracked solder joints around the power stage, corroded edge connectors, and blown output transistors after a supply fault.
Every kdm inverter we supply is inspected before dispatch. Each unit is checked for physical damage, correct marking and the specific wear or degradation patterns that matter for this class of component, then packed to survive international transit. Where a superseded revision is the only one available, we say so plainly and explain the substitution, so the installing engineer can make an informed decision rather than discovering the difference on site.
Buying guidance and compatibility notes
Before ordering the kdm inverter, confirm three things. First, the controller catalogue number and the board revision letter, plus the fault code stored in the controller memory. Second, the same board is frequently fitted across several controller families, so the equipment model alone is not enough to identify the right revision. Third, whether the installation is a traction lift or an escalator, since duty cycle and loading differ between the two.
On fitting, one point is worth repeating: discharge the DC bus before removing a power board, and photograph the connector layout before you unplug anything. Almost every repeat failure we see on kdm inverter traces back to a related component that was left in place, or to an adjustment that was assumed rather than measured.
Control electronics dominate the failure statistics on any lift older than about twelve years. The boards themselves are usually sound; what fails is the surrounding hardware — capacitors that have dried out, connectors that have oxidised in a humid machine room, and solder joints that have cracked under years of thermal cycling.
A controller board carries the whole logic of the installation on one or two PCBs. The underlying cause is often aging electrolytic capacitors that have lost capacitance rather than failed outright.
When a drive or mother board is replaced, it is worth checking the DC bus capacitors and the cooling path at the same time. A board that failed from overheating will fail again if the fan or heatsink is left as it was.
The main board is the component that a service engineer reaches for first when a lift stops without a mechanical cause, and the symptom that most often brings an engineer to it is a lift that travels but refuses to level or open its doors.
If you are unsure which variant of the kdm inverter you need, send a photograph of the nameplate and the existing component alongside a description of the fault. That is usually enough for our team to identify the correct replacement without a site visit, and it avoids the cost and delay of returning an incompatible part. We are also happy to advise on the other serviceable items in the same control board / PCB group, so a planned shutdown can cover several wear items at once.
Related parts and further reading
Because kdm inverter is only one item in the control board / PCB group, these related pages may help you plan the work:
- Elevator spare parts
- Door Operator Controller
- Elevator Display
- Elevator Encoder
- Elevator Service Tool
Reference sources
The compatibility information on this page was cross-checked against the following authoritative references. Always confirm the exact reference against your own equipment nameplate.
